H03 \820651
8 MULLER Looms, mod. NF53, yoc 2007/2002, 6/42, 220 Volts/60 Hz/3ph

H03 \820652
8 MULLER Looms, mod. NF53, yoc 1999, 6/42, 220 Volts/60 Hz/3ph.

H03 \820869
2 MULLER Looms for labels, mod. NF N 53, yoc 1995

H03 \820761
6 MULLER Looms for labels, mod. MVC, yoc 1990 about.

H03 \820765
7 MULLER Looms for labels, of which:
(2) mod. MC-100, yoc 1980 about
(5) mod. MCE-100, yoc 1985 about
Sold only as a whole lot.

H03 \818335
1 MAGEBA Polyester line, yoc 2000, mangle, pre-dryer and dryer, methane gas heating, production capacity minimum 4500 m./day each end, table width 40 cm. (normally 10 ends assembled).
1 MAGEBA Cotton line, yoc 1983, mangle, steaming cabinet 60 m., 6 washing vats,  roller dryer methane gas heating, production capacity minimum 4500 meters/day each end, table width 20 cm.
1 MAGEBA Sizing machine double roll, table 20 cm., methane gas heating.
5 GEL Winding machines
Grey ribbon preparation system for dyeing composed of:
Creels for beams of grey ribbon.
Flanged Beams in wood for grey ribbon ghost in PVC about 200.
1 GTM Winding System for the same (at 3 positions) to wind ribbon produced by the looms.
6 Winding Systems.
Fittings
1 HASHZUME Knotting machine mod.T-1.
1 OMM Loom type NS  6 heads x  5/30  m/m., complete with creel

H06 \820397
1 DORNIER EASY LENO Rapier loom, mod. PTSL 16, yoc 2005, width 1900 mm.
With upper beam.
With accessories.

H06 \820754
6 DORNIER Looms, mod. HTVS 4/S, yoc 1996, width 1900 mm., Staubli dobby type 2667, 16 shafts installed.
With accessories.

H06 \818987
2 DORNIER Looms, mod. HTVS8S, yoc 1995, width 2200 mm., 4 ECS, Staubli dobby type 2660 20 shafts, DP1, Electronic warp let off, Electronic take up.
With accessories.

H09 \820817
3 SOMET Looms, mod. ALPHA HD, yoc 2004, w.width 2100 mm., PGA transfer fitted on the machines, electronic Fimtessile dobby mod. 7P, 20 shafts fitted, 8 colours.
With accessories.

H09 \820818
3 SOMET Looms, mod. ALPHA, yoc 2002, w.width 2100 mm., Staubli dobby type 2670, 20 shafts, 8 colours.
With accessories.

H09 \820663
2 SOMET Looms, mod. MASTER SM93, yoc 1990, width 1900 mm., Staubli mechanical dobby type 2232, 16 shafts, 8 colours.
With accessories.

H09 \820774
2 SOMET Looms, mod. MASTER SM92, year 1987, width 2200 mm., with Staubli dobby type  2660, 20 lever.
With accessories.

H10 \820555
1 SULZER Loom, mod. P7300HP V8 S 540 N 2 EP D12, yoc 2008, width 5400 mm.

H10 \820766
1 SULZER Loom, mod. P7200 B390 N2 EPRQ D1

H10 \820768
1 SULZER Loom, mod. P7150  B190 N4 SP D1, yoc 2000, with Staubli dobby type 2665 12 shaft

H10 \820103
8 SULZER Looms, mod. P-7100 B390 N2 EPRQD1, yoc 1998/97, width 3900 mm., 10 cams, twin beam.

H10 \820767
1 SULZER Loom, mod. B390 N 1-1 EP D1 M
1 SULZER Loom, mod. B390 N4 EPQ R D1

H11 \819175
6 VAMATEX Looms, mod. LEONARDO, yoc 1998, width 2100 mm., dobby 20 shafts. Fimtessile mod. RD840/S
Electronic Let-off and take up.
With accessories.

H11 \820096
8 VAMATEX Looms, mod. P1001 SUPER EK, yoc 2002, width 1900 mm., Fimtessile dobby type RD-860, 20 shafts installed, 8 colours except 1 loom with 12 colours.
With electronic colour selector.
With accessories.

H11 \820338
2 VAMATEX Looms, mod. P1001 ES FULL MOT, yoc 1995, width 1900 mm., Fimtessile dobby type RD 840, 20 shafts, with electronic let off and take up.
1 VAMATEX Loom, mod. P1001 ES FULL MOT, yoc 1994, width 1900 mm., Fimtessile dobby type RD 810, 20 shafts, with electronic let off and take up.

H11 \817638
2 VAMATEX Looms, mod. P-1001 ES, yoc 1995/1996, width 1900 mm., electronic dobby, electronic warp let-off, ECS.
With accessories.

H11 \819458
1 VAMATEX Loom, mod. P-1001, yoc 1990, 6 cam Fimtessile.
With accessories.

H11 \820427
1 VAMATEX Loom, mod. PROPELLER, yoc 1992.
4 VAMATEX Looms, mod. P1001ES, yoc 1994/1995/1997/2000.
All width 1900 mm., Fimtessile dobby 20 shafts.
With accessories.

H13 \820770
1 DORNIER Air jet loom, mod. AWV6S, yoc 2002, width 2100 mm., 6 colours, Staubli dobby  type 2871, 16 shafts
With accessories.

H13 \819583
N.4 DORNIER Air Jet looms, mod. LWV 4/4, yoc 2000, width 3600 mm., 4 colours, cam motion, max 4 cam, 4 cams fitted.
With accessories.
N.1 DORNIER Air Jet loom, mod. LWV 4/8, yoc 2000, width 3800 mm., 4 colours, cam motion, max 8 cam, 4 cams fitted.
With accessories.

H13 \819744
6 DORNIER Air jet looms, mod. LWV8/S, yoc 1998/1999/2000, width 3600 mm., 8 colours, Staubli electronic dobby type 2677-P1 with 16 shafts.
With accessories.

H13 \817754
*22 DORNIER Air jet looms, mod. LWV2/E, yoc 1995, width 2800 mm., 2 colours, cam.
*  3 DORNIER Air jet looms, mod. LWV2/E, yoc 1995, width 3400 mm., 2 colours, cam.

H13 \819319
1 DORNIER Air jet loom, mod. LWV4/E, yoc 1993, width 2800 mm., Dialog Panel 2, Electronic fabric take-up and let-off, 4 colours with Servo Control, Selvedges tying system Disco Leno, Cam motion Staubli 1627 - 6  shafts, Grob stop motion device, Prepared for beams flange diam.1000 mm.
With accessories.

H13 \820635
6 PICANOL Air jet Looms, mod. OMNI 2R, yoc 1994, width 3400 mm., cam box STAUBLI 1620 (capacity 6 cams - installed 4), lateral and central tucking device, 2 colours, electronic let off, mechanical take up
With accessories.

H13 \820622
4 TSUDAKOMA Air jet looms, mod. ZAX, yoc 2000, width 2300 mm., 4 colours, Staubli dobby type 2871, 16 shafts, beam flange diam. 900 mm.

H16 \820816
1 DORNIER Loom, mod. HTV8/J, yoc 1999, width 3600 mm., Staubli Jacquard type LX1600 yoc 2000, 5120 hooks (4800 installed), controller JC5, module M5/2.
Electronic Warp Let off and electronic take up, twin beam, DP2.
With accessories.

H16 \814674
2 DORNIER Air jet looms, mod. LWV6/J, yoc 1995, width 3600 mm., 6 colours, Staubli Jacquard type CX-880, yoc 2000, 2688 hooks (2400), controller JC5, module 4, updated DIALOG PANNEL 2.
With accessories.

H16 \820499
1 PANTER Loom, mod. E5XP, yoc 2004, width 1900 mm., with BONAS Jacquard 2400 hooks, controller S600, with harness 15600 ends (14.400 used)
With accessories.

H16 \819248
2 SOMET ALPHA PGA hi-drive single beam version, yoc 2011, nominal width 3200 mm., simple beam, 8 electronic colours, electronic let-off, electronic take-up, central cutter, ready for inverter; electronic Staubli Jacquard type DX100 format 2688/2400 hooks installed, CNTR JC6, 32 ends/cm.
With accessories.

H16 \820764
3 SULZER Looms, mod. G6200, yoc 1994/93, width 1900 mm. doble ensuple, with Staubli Jacquard type CX960, 2400 hooks installed, JC4 controller, M4 module.

H16 \820808
2 VAMATEX Looms, mod. LEONARDO, yoc 2002, width 1900 mm., with Staubli Jacquard Jumbo type LX 3201, 6912 hooks (prepared for 8192), JC5 controller, M5, 8 & 12 colours, Electronic take-up.
Complete with harness 96 ends/cm. and structure.
With accessories.

H16 \820478
1 VAMATEX Loom, mod. LEONARDO, yoc 1999, width 1900 mm., 12 colours, double beam, Bonas Jacquard yoc 1999, 2400 hooks, controller S250 6MB, with harness 14880 ends, 100 ends/cm.
With accessories.

H16 \820813
6  VAMATEX Looms, mod. LEONARDO, yoc 2000, width 3400 mm., 8 colours, Staubli Jacquard type  CX-870, 2688 hooks (2400 installed), controller JC5, Module M4.
With accessories.

H17 \820171
1 Staubli double Jacquard, type CX-860, yoc 1993, 4800 hooks (2x2400), JC4, M3.

H20 \819308
1 Automatic embroidery machine, yoc 2009, 3 double heads, needles distance 275 t mm., with accessories

H20 \819307
1 Automatic embroidery machine, yoc 2007, 6 double heads, needles distance 275t mm., field depth 700 mm.

H20 \819320
2 COMERIO ERCOLE Embroidery machines, type EC 15/108N, 1982, embroidery ratio max. 108/4., length 13,716 m.; the machines have been modified as follows:
- addition of electronic equipment cascafili model CF4
- (1) machine with full electronic modification made by BIESSE
- (1) machine with the modification to read drawings on floppy disk from a PC instead of reading drawings from cardboard

H20 \820078
1 LASSER Embroidery machine, mod. KL83-155-DISC 10 YD, yoc 1989, 10 yards, one level, 9000 mm. x width 1500 mm.
Equipped for application of soutage, paillettes, braid/ ribbon, fantasy yarns, etc.
Complete with:
Set 24/4 heads soutage (n.57 + spare parts) + set 12/4 heads paillettes (n.114 + spare parts) + set 12/4 heads braid / ribbon (n.114 + spare parts)

H21 \818244
TERROT Circular knitting machines.
More info on request

H21 \820404
1 Installation of 15 circular knitting machines ORIZIO/MARCHISIO/ALBI/VIGNONI/SINGER for double and single jersey, 30".
The plant is sold only totether.
More details on request.

H21 \818716
Lace braiding machines, mechanical and electronics looms, for cotton/flax/synthetic (viscose or polyester), width from 5 mm. to 250 mm.
Some machines have been modified from Jacquart to electronic with pneumatic operation.
2 Pirn winders HACOBA
More info on request

H22 \817403
1 CTM machine for sample cutting, type VT-SZ, yoc 1995, w. width 1900 mm. , complete of electronic countermeter and automatic cutter

H99 \819646
1 GIOVANNELLI Beams store, 60 positions, beams h.3600 mm. x diam.1000 mm.

H99 \819647
1 GIOVANNELLI Beams store, 60 positions, beams h.2200 mm. x diam.1000 mm.

H99 \817689
25 TECNOTEAM Inspection tables accessories for looms, width 2100 mm., (3) with Inverter and (7) with potentiometer.

G02 \819880
1 KNOTEX Knotting machine yoc 2011, trolley width 2600 mm., with accessories.

G02 \817529
1 STAUBLI Knotting machine, type TOPMATIC TPM 210 PC, yoc 2004, 1 trolley larg.3200 mm.

G02 \818222
1 TITAN Knotting machine mod.KM6H-AS, with trolley width 2200 mm.
Machine mechanically tested recently.

G05 \820068
1 ELM  Drawing in machine mod. VEGA XL 2300 yoc 1998, 18 frames positions, equipped with special trolley.

G05 \813150
1 EL&M Autom. drawing-in machine, mod. VEGA K, yoc 1992, 2 trolleys.

G05 \815886
1 USTER Drawing-in machine, mod. DELTA 1, yoc 1988, 2 trolleys2200 mm

G05 \816658
1 USTER Semi-autom. drawing-in machine, width 2400 mm.

G07 \820829
1 BENNINGER creel at rotary panels, yoc 1995, 560 positions, gauge 240 mm., internal loading

G07 \820830
1 KARL MAYER creel at trolleys, yoc 2002, 480 positions, gauge 300 mm., anti balloon: automatic timed air maintenance.

G08 \819811
1 BENNINGER Direct Warper, mod. BEN-DIRECT, yoc 2000, width 3400 mm., with BENNINGER Creel yoc 2000, 1056 positions, gauge 330 mm.

G08 \818041
1 KARL MAYER direct warper, mod. DS42/32NC1, yoc 1998, gauge 42”x32”, with creel 1408 positions, 2 sides x 4 ranks x 2 levels, length 23 m. x h.5 m. x width 5/6 m., with tensioners thread thread.

G08 \814987
1 LIBA EXPANDER TP-19E Warper for elastomer
Reconditioned and replaced the electric plant (d.c.)
Motorized creel for deroulé prepared for 704 positions of which 688 effectives.
For warping of beams width 22" with flange diam.523 mm.
Equipped with Liba software to compensate the stretch differences inside of the cone.

G08 \816752
1 RAMALLUMIN warper, mod. BF, yoc 1991, flange max. diam.1250 mm. x h. 1500 mm., feeding C.C., max. speed 900 mt/min., 10 subbi, with parallel creel, 504 positions, gauge bobbins diam. 350 mm., 7 trolleys at 6 levels, electric warp stop motion, 1 blower

G08 \817501
1 RAMALLUMIN direct warper, yoc 1985, width 1800 mm.

G08 \820064
1 ROSTONI Direct Warping machine mod.ODT 22 de 1993, w.width 1600 mm., beam flange diam.760 mm.

G09 \816793
1 HERGETH Sample Warper, yoc 1992 modified in 2002, Rostoni creel 240 positions.

G09 \819831
3 HERGETH Sample Warpers.

G09 \812199
1 HERGETH Sample warper, width 1800 mm., chain 8 m. and multiple max 32 m., creel with 5 feeders, computer.

G09 \816338
1 HERGETH Sect. Warper, width 1800 mm., warping length 11974 mm., 10 yarns
AITA electronic programmator.

G09 \820297
1 SUZUKI Sample Warper mod.NAS 140A S2250 yoc 2002, with rotary creel 8 colours and standard creel 10 colours.

G10 \820036
1 Sectional warper BENNINGER, mod. BEN TRONIC, yoc 2003, width 220 cms, cone ratio 1:5
Machine complete with PRESSING  device and WAXING device.
2 Parallel Creel Benninger TROLEYS TYPE, 480 positions, pitch 270x270 mm
2 automatic leasing device BEN SPLIT
Voltage: 380 Volts-50 Hz.

G10 \820037
1 Sectional warper BENNINGER, mod. BEN TRONIC, yoc 2003, width 220 cms, cone ratio 1:5.
Machine complete with pressing device and waxing device.
1 Parallel Creel Benninger TROLEYS TYPE, 480 positions, pitch 270x270 mm
1 automatic leasing device BEN SPLIT
Voltage: 380 Volts-50 Hz.

G10 \820617
1 BENNINGER Sectional warper, mod. BENMATIC, w. width 2200 mm, yoc 1998.
1 BENNINGER Creel with swivel frames, 570 positions, 8 floors, rejection 22 cms, yoc 1996.

G10 \820809
1 BENNINGER Sect. Warper, mod. ERGOTEC, yoc 2008, width 3800 mm., max flange beam diam.1000 mm., ratio conicity 1/7.5
Complete with:
1 BENNINGER Creel, mod. BEN-CREEL, 840 positions, horizontal and vertical gauge 200 mm.

G10 \819445
1 BENNINGER Sect. Warper, mod. ERGOTRONIC, yoc 1996, larg. 2200 mm., creel at trolleys, 640 positions, blower.

G10 \818954
1 BENNINGER Sect. Warper, mod. ERGOTRONIC, yoc 1996, width 2200 mm., cone ratio 1:8-1450, sizing system, pressing device, for beams flange diam. 800 mm.
Bengard Creel, 521 positions, gauge 540-240 mm.

G10 \819806
1 BENNINGER Sect. Warper, mod. ERGOTRONIC, yoc 1995, nominal width 3400 mm., wrap-reel/cone 1210/1050 (1:5) 800 mm., electronic controls for section, max flange diam. 1000 mm., yarn tension element of creel BEN CREEL type GAA/GZB, 640 cones positions on 8 levels, gauge 270 mm., yarn tension motorized with BEN-GUARD GFA.

G10 \811764
1 BENNINGER Sect. Warper, mod. SC, yoc 1983 about, width 2200 mm., can accept beams diam.1000 mm., with BENNINGER Creel yoc 1986, 560 positions, gauge 240x240 mm., sizing device.

G10 \818221
1 BENNINGER Sect. Warper, mod. SFA, yoc 1981, width 2200 mm., for beams flange diam.1000 mm., with creel 278 positions.

G10 \817235
1 BENNINGER Sect. Warper, mod. SFA, yoc 1981, width 2200 mm., creel 400 positions.

G10 \820784
1 BENNINGER Sectional Warper, mod. SUPERTRONIC 2200/1700/212,5 MM., yoc 1995, width 1800 mm., ratio 1:8, flange max. diam. 1000 mm., without creel.

G10 \820017
1 BENNINGER Sect. Warper, mod. SUPERTRONIC, yoc 1993,  width 2200 mm., waxer, pressure roller, Benninger creel 432 positions (8 level), horizontal gauge 400 mm., vertical gauge 240 mm.

G10 \809873
1 BENNINGER  Sect. Warper, type SUPERTRONIC, yoc 1991, width 2200 mm., beam  flange diam.1000 mm., ratio 1:5,  waxer, with creel 240 positions.

G10 \820504
1 BENNINGER Sectional Warper, mod. SUPERTRONIC, yoc 1990, width 2100 mm., with Benninger creel 342 positions.

G10 \819484
1 BENNINGER Sect. Warper, mod. SUPERTRONIC, yoc 1988, revised in 1999, width 2200 mm., creel with 320 positions on 8 levels.

G10 \818274
1 BENNINGER Sect. Warper, mod. SUPERTRONIC, yoc 1987, width 2200 mm., cone ratio 1:5-1300, sizing system type Cantono, pressing device, Beaming at 2 speed, max speed 220 m./min.
Creel 512 positions, gauge 540-270 mm.
Yarn stop motion type GFA.

G10 \819705
1 BENNINGER Sect. Warper, mod. SUPERTRONIC, yoc 1986, width 2200 mm., cone ratio 1:5, with pressure rollers and waxing system, electronic tension controle, beams diam.1000 mm., double exit speed, warping speed 800 m./1', creel mod.GBA/GZB yoc 1989, 512 positions, horizontal and vertical gauge 270 mm.

G10 \819037
1 BENNINGER Sect. Warper, mod. VERSOMAT, yoc 2009, w.width 2200 mm., cone length 1152 mm.(useful 970 mm.), 1:6, max beam diam.700 mm., max speed 750 m./m.
With:
Benninger Creel of 464 positions (8 levels), gauge 270x270 mm.

G10 \818982
1 BENNINGER Sect. Warping, mod. VERSOMAT, yoc 2007, width 2200 mm., creel 304 cones (8 levels),  waxer

G10 \820172
1 BENNINGER COMAT Sect. Warper yoc 1985, w.width 2200 mm. (on beam 2250 mm.), cone length 1500 mm., with creel of 288 positions.

G10 \816313
1 COMAT Warper, mod. SF, yoc 1980,  width 2200 mm., with creel

G10 \818807
N.1 GAMATEX Sect. Warper, mod. G410/m², yoc 2000
Beaming G165M2
W.width 3300 mm., width 3300 mm., flange diam.1000 mm.
Fix cone 1:5
Control warping functions with Omron computer.
without sizing system
N.1 ROSTONI Creel, mod. RCF/608, yoc 1994.
600  positions on 8 levels with gauge 250 mm. x 250 mm.
Yarn tensioning device mod.R/LCR-B.
Ceramic yarn guide
Sensors for stopping of yarn breakage.
Motorized opening pannels on both sides.

G10 \819170
1 GIOVANNELLI Sect. Warper, mod. COMPACTRONIC 2000, yoc 2007, width 2200 mm., cone 11°, beam diam.1000 mm., without creel.

G10 \817369
1 HACOBA Sect. Warper, mod. USK T 1000, yoc 1991, width 4000 mm., no creel.
Machine refurbished with new PC.

G10 \810534
1 KARL MAYER Sect. Warper, type ECON-O-MATIC, yoc 1995, complete of BML beaming unit for the production of the middle-sized warpers, w. length 2250 mm., max. cone diam. 1075 mm.,
Linked to:
1 ROSTONI creel, type RFG 240, 240 spindles, vertical gauge: 240 mm., horizontal gauge 540 mm.
More details on request

G10 \819304
1 KARL MAYER Sect. Warper, mod. ECONOMATIC, yoc 1999, width 2200 mm., sizing system, with:
1 ROSTONI Creel, rotary panels, 240 positions, 6 ranks, automatic leasing.

G10 \819036
1 KARL MAYER Sect. Warper, mod. ECONOMATIC, yoc 1998, width 2250 mm., with KARL MAYER Creel 240+240=480 total positions.
This machine inserts the lease automatically.

G10 \820062
1 KARL MAYER Sect. Warper, mod. ECON-O-MATIC, yoc 1998, width 2200 mm., double frames device, wax device, complete with:
1 KARL MAYER Creel, type GN-1-480, yoc 1998, 480 positions (240x2), horizontal gauge 270 mm., vertical gauge 270 mm., tension devices KFD.

G10 \819449
1 KARL MAYER Sect. Warper, mod. ECON-O-MATIC, yoc 1997, width 2200 mm., max warping width: 2250 mm., warping drum diam. 825 mm., warping drum circumference: 2590 mm., max winding diameter: 1075 mm., max winding height: 125 mm., warping speed: 50 - 600 m/min., feed: 0.02 - 9.99 mm./rotation, minimum warping length: 10 m., max yarn tensile force of beaming yarn: 600 n (newton), warping section width: 15 - 230 mm., beaming: total length of beam: 3000 mm., diam. 1000 mm., max beaming speed: 75 m/min., max yarn tensile force: 3500 n (newton)
complete of 2 creels: 640 positions (320x2 sides), gauge: horiz. 270 mm., - vertical 270 mm.

G10 \820795
1 KARL MAYER Sect. Warper, mod. ECON-O-MATIC, yoc 1996, width 2200 mm., double frames device, wax device, complete with:
1 KARL MAYER Creel type GN-1-800 yoc 1996, 800 positions (400x2), horizontal gauge, vertical gauge, distance between cones: 220/240 mm., 10 floors, brakes type KFD

G10 \819436
1 KARL MAYER Sect. Warper, mod. ECON-O-MATIC, yoc 1996, w.w. 2200 mm., COMAT creel with 336 positions (21x2x8 levels), gauge 270 mm., for woollen bobbins max. diam. 220 mm.

G10 \815600
2 TAIANA Sect. Warpers, mod. 300 of which:
(1) yoc 2001, with creel defilé, mod.TF80P, 640 positions, gauge 220 mm.
(1) yoc 1997, updated 2001, with creel defilé mod.TF80P, 576 positions, gauge 220 mm.
All: w.width 2400 mm., drum circumference 2500 mm., cone adjustment from 0 to 300 mm., cone w.width 1000 mm., max flange diam.800 mm., 380 Volts/50 Hz.
For silk/cotton/wool/linen/polyester/viscose/nylon yarns.

G10 \812571
1 TAIANA Sect. Warper, mod. 400, yoc 1987/88, w. width 3600 mm., flange max diam. 1000 mm., 380 Volts, creel of 630 positions.

G10 \816834
1 TAIANA Sect. Warper, yoc 1981, electrically reconditioned in 2002, width 3600 mm., max flange diam. 800 mm., with 1 creel  of 600 positions, gauge 200 mm., removable trolleys.

G10 \816940
1 TAIANA Sect. Warper, mod. 400, yoc 1995, width 3600 mm., creel 608 positions, gauge 270 mm., removable trolleys.

G11 \820351
1 BENNINGER Beaming machine, yoc 2006, w. width 3800 mm., flange diam.1000 mm.

G11 \820423
1 ATELIERS DE BELMONT Re-beaming machine, mod. ASF 32, yoc 2003, width 3200 mm., beam flange diam. 1000 mm., waxing device.

G12 \818161
1 GA.MA.TEX sizing machine, yoc 1989, 16/18 beams, complete of 2 vats

G12 \820418
1 ROTAL Sizing machine, mod. C110/450, yoc 1998
Feeding 20 beams width 2000 mm.
1° Size box ROTAL double deep and double squeeze
1 Dryer with 2 cylinders
2° Size box ROTAL double deep and double squeeze
1 Dryer with 14 cylinders
1 Beaming Unit cylinder width 4200 mm., flange diam.1100 mm.
Colours Kitchen.
1 KARL MAYER Direct Warper, mod. BEN DIRECT ZS/98, yoc 2011, width 2000 mm., beam flange diam. 1000 mm., with V creel of 620 positions, gauge 300x330 mm. about.

G12 \820839
1 ROTAL Sizing machine, yoc 1988
Creel 12 beams h.2000 x diam.1000 mm.
1 Size box  width 2150 mm., double deep and double squeeze.
Dryer cylinders width 2200 mm., 2 pre-dryeing tefloned cylinders and 8 dryeing cylinders of which 4 tefloned.
Beaming width 3400 mm. with beam diam. 1000 mm.
Sizing kitchen.

G12 \820788
1 ROTAL - KARL MAYER sizing machine, table width 1.900 mm, sizing box yoc 2000, 2 divers and 2 squeezers.
- Cylinder dryer, table width 1900 mm., 9 cylinders
- Beaming Head max width 3200 mm., with beam diam.1000 mm. with automatic humidity control in output
- Electrical panel, display with sizing box tension control.
- Sizing kitchen composed of:  1 preparation tank 700 lts. + 2 storage tanks 1100 lts. each
- 16 Beams
- 1 mobile trolley for sectional
- Steam distribution system with automatic valves regulation, yoc 2011
Machine supplied with humidity control device

G12 \819965
1 RAMALLUMIN / SUCKER Sizing machine, renewed in 1991
Ramallumin Double pass wetting unit with sizing bath temperature control.
Sucker Steam Dryer at 9 cylinders.
Ramallumin Beaming Unit with thread sorting section moist controller Mahlo Textometer RMS-7
2 Beams holder for 4 beams diam.800 mm.
3 beams holder for 4 beams diam.1000 mm.
24 Beams diam. 800 mm. + 12 beams diam. 1000 mm. Jametti
Giannazza Sizing bath cooking unit.

G12 \818240
1 SUCKER MULLER Sizing machine, 1985, composed of:
*Beaming head type WN
*Feeding creel 16 beams width 2800 mm.
*1(one)size box Double impregnation
*Dryer 12 cylinders of which 8 tefloned.
*Delivery width 3600 mm. diam.1000 mm.
*MAHLO Texsole Dryeing control system.
1 BENNINGER Direct Warper, yoc 1985, width 2800 mm., V creel.

G12 \820559
1 SUCKER Sizing machine, mod. ZTWL, width 2300 mm., yoc 1984 - completely reconditioned in 2002.
• Head machine mod. WL, w. width 2300 mm. = 90 Inches
• 2 sizing box mod. LC
• 4 pressure rollers
• 7 + 2 drying cylinders
• 1 sectional beam unwinding breaker.
• MAHLO moisture control
• Dust suction apparatus
- Preparation sizing kitchen, mod. mod. TK (600 lts), 2 tanks (800 lts.).
- Major spare parts (original Sucker).
More info on request

G12 \820722
1 SUCKER MULLER Sizing machine, mod. SDR 40, yoc 1988 - refurbished in 2002, 3200 mm. w. width of headstock, max diam. of  flanges 800 mm, composed of:
-warp beam stand with 16 beams capacity (modular version)
-2 x double nip and dip model AB300 size boxes
-2 level dryer model ZS/4/4/4 - for 12 cylinders (8 of them are Teflon covered)
-Mahlo Textometer - RMS-7 - humidity control
-size preparation and size storage tanks - model EW 14 (2 tanks x 1000l capacity)
Machine complete, in very good condition.

G12 \820067
1 SUCKER MULLER Sizing machine, yoc 1966, width 2000 mm., squeezing cylinders width 2150 mm., dryers cylinders width 2000 mm., 7 dryers cylinders, equipped with 2 sizing box type SE 40 yoc 1988.

G12 \820303
1 TMT Tangential Sizing machine, yoc 2009, 4 tangential heads, PLC + INVERTER.

G12 \818183
1 TMT Sizing machine, mod. WR1000, yoc 1997, width 2200 mm., 3 sets of lights above and below, inverter, double mangle, for beams diam. 1000 mm.

G12 \806854
1 Warping and sizing line for filament yarns, composed of:
-ROSTONI Creel, 1440 positions on 2 levels, rotary panels.
-TSUDAKOMA Sizing machine, mod. KSH-500, yoc 1989, width 2000 mm., max flange diam. 914 mm.
-ARCT / MECATEX Beaming machine, yoc 1992, 16 direct beams of 2000 mm., max height of beam 3200 mm., max flange diam. 1000 mm.

Last updating: 18.02.2015